MW Mean Well Meanwell 200W Constant Voltage PWM Output KNX LED Driver PWM-200-KN Series

Features

Constant Voltage PWM style output with user changeable frequency up to 4KHz compliant IEEE1789-2015 and EU Ecodesign SVM requirement
Min. dimming level 0.01%
Plastic housing with class II design
Standby power consumption<0.5W
Integrated KNX control protocol
No need KNX-DALI gateway
Typical lifetime>50000 hours
5 years warranty

Mean Well KNX LED Driver PWM-200-KN Series Data Sheet Download

Mean Well KNX LED Driver PWM-200-KN Series

Description

PWM-200-KN series is a 200W AC/DC LED driver featuring the constant voltage mode with PWM style output, which is able to maintain the colour temperature and the brightness homogeneity when driving all kinds of LED strips and constant voltage LED bulbs.The built-in KNX interface is to avoid using the complicated KNX-DALI gateway and equipped with KNX Data Secure. KNX Data Secure offers protection against manipulation in building auto mation and can be configured in the ETS project. PWM-200KN operates from 100~305VAC and offers models with output voltage between 12V & 48V. Thanks to the high efficiency up to 94%, with the fanless design, the entire series is able to operate for -40°C ~ +85°C case temperature under free air convection. The minimal dimming level low to 0.01% is suitable for low light level applications e.g. cinema. The output frequency is changeable up to 4KHz complaint IEEE1789-2015 no risk requirement and EU Ecodesign stroboscopic visibilitymeasure(SVM) requirement providing a great solution for health concern due to light fickering.

Mean Well KNX LED Driver PWM-200-KN Series Model Encoding

Type	Function	Note
KN	KNX control technology	In stock
KNBST	KNX control technology with BST14 connector	by request

Specification

MODEL		PWM-200-12	PWM-200-24	PWM-200-36	PWM-200-48
OUTPUT	DC VOLTAGE	12V	24V	36V	48V
	RATED CURRENT	15A	8.3A	5.55A	4.17A
	RATED POWER	180W	199.2W	199.8W	200.1W
	DIMMING RANGE	0 ~ 100%
	PWM FREQUENCY (Typ.)	200~4000Hz user changeable via ETS
	SETUP, RISE TIME Note.2	500ms, 80ms/230VAC, 1200ms, 80ms/115VAC
	HOLD UP TIME (Typ.)	10ms/230VAC or 115VAC
INPUT	VOLTAGE RANGE Note.3	100 ~ 305VAC 142 ~ 431VDC (Please refer to “STATIC CHARACTERISTIC” section)
	FREQUENCY RANGE	47 ~ 63Hz
	POWER FACTOR (Typ.)	PF>0.97/115VAC, PF>0.96/230VAC, PF>0.94/277VAC @ full load (Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
	TOTAL HARMONIC DISTORTION	THD<20% (@load≧60%/115VAC, 230VAC; @load≧75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION” section)
	EFFICIENCY (Typ.)	92%	93%	94%	94%
	AC CURRENT (Typ.)	2.2A / 115VAC 1.1A / 230VAC 0.9A / 277VAC
	INRUSH CURRENT (Typ.)	COLD START 65A (twidth=550μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
	MAX. NO. of PSUs on 16A CIRCUIT BREAKER	3 units (circuit breaker of type B) / 5 units (circuit breaker of type C) at 230VAC
	LEAKAGE CURRENT	<0.75mA / 277VAC
	STANDBY POWER CONSUMPTION	standby power consumption<0.5W when dimming off
PROTECTION	OVERLOAD	108 ~ 135% rated output power
		Hiccup mode or Constant current limiting, recovers automatically after fault condition is removed
	SHORT CIRCUIT	Shut down o/p voltage, re-power on to recover
	OVER VOLTAGE	13 ~ 18V	27 ~ 34V	41 ~ 49V	53 ~ 65V
		Shut down o/p voltage, re-power on to recover after fault condition is removed
	OVER TEMPERATURE	Shut down o/p voltage, re-power on to recover after fault condition is removed
ENVIRONMENT	WORKING TEMP.	Tcase=-40 ~ +85℃ (Please refer to “OUTPUT LOAD vs TEMPERATURE” section)
	MAX. CASE TEMP.	Tcase=+85℃
	WORKING HUMIDITY	20 ~ 95% RH non-condensing
	STORAGE TEMP., HUMIDITY	-40 ~ +80℃, 10 ~ 95% RH
	TEMP. COEFFICIENT	±0.03%/℃ (0 ~ 50℃)
	VIBRATION	10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY & EMC	SAFETY STANDARDS Note.5	Ul8750 (type” HL”), CSA C22.2 No. 250.13-12; ENEC BS EN/EN61347-1, BS EN/EN61347-2-13, BS EN/EN62384 independent, EAC TP TC 004, GB19510.1, GB19510.14, IS15885(Part2/Sec13) (except for 36V) approved; Design refers to BS EN/EN60335-1, According to BS EN/EN61347-2-13 appendix J suitable for emergency installations
	KNX STANDARDS	Certified protocol
	WITHSTAND VOLTAGE	I/P-O/P: 3.75KVAC
	ISOLATION RESISTANCE	I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH
	EMC EMISSION Note.6	Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C (@load≧60%) ; BS EN/EN61000-3-3, GB17743 and GB17625.1,EAC TP TC 020
	EMC IMMUNITY	Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity, Line-Line 2KV), EAC TP TC 020
OTHERS	MTBF	1658.9 K hrs min. Telcordia SR-332 (Bellcore); 170 .0K hrs min. MIL-HDBK-217F (25℃)
	DIMENSION	1956839.5mm (LWH)
	PACKING	1.03Kg; 12pcs/13.4Kg/0.71CUFT

Applications

LED strip lighting
Indoor LED lighting
LED decorative lighting
LED architecture lighting
Type HL for use in class I, division 2 hazardous (classified) location.
Cove lighting
Industrial lighting

Mean Well KNX LED Driver PWM-120-KN Series Video Show

Find us on SNS

You can find us and know more about us on SNS: